Hi, Wayne here from Sears PartsDirect.
Today we're going to troubleshoot a riding lawn mower engine that spins but won't start
when the starter motor runs.
Once it's spinning, the engine needs 3 things to run—fuel, spark and compression.
Here's a quick test that can often eliminate 2 of those suspects right away.
We'll check to see if the engine has compression and spark by spraying a short burst of starter
fluid into the engine's cylinder.
The highly combustible starter fluid will start the engine briefly if the cylinder gets
spark and the right amount of compression.
In a well-ventilated area, pull off the air filter and spray a short burst of starter
fluid into the cylinder through the carburetor's air intake.
Now try to start the engine.
If the engine doesn't start at all, you can skip to the next section on fuel system
troubleshooting and move on to checking the ignition system.
If the engine starts briefly and then dies, you know the spark and compression are okay,
leaving you with a fuel supply problem.
A dirty carburetor is usually the culprit when the engine isn't getting fuel.
But, before you replace or rebuild the carburetor, check these basic fuel supply issues so you
don't waste money on a part that you don't need.
If the air filter you just pulled off is dirty, replace it.
You need a clean air filter so the right amount of air can mix with the fuel to start the
engine.
If you haven't used the mower for several months, drain and refill the fuel tank with
fresh gas.
Over time, gas absorbs water and loses combustibility.
In the future, if you don't use up all the gas before storing your riding mower for several
months, add fuel stabilizer to your gas tank.
A clogged fuel filter won't allow gas to flow to the carburetor.
Replace the fuel filter if you haven't changed it within the last year.
Here's a video that shows you how.
The fuel solenoid valve shuts off fuel to the carburetor to prevent backfire when you
kill the engine.
If the wire's disconnected, the solenoid won't open to allow fuel to flow to the carburetor.
Check the wire harness connection on the fuel solenoid valve.
Reconnect the valve wire harness if you find it disconnected.
Check the fuel line from the fuel tank to the carburetor for clogs or damage.
Clear any clogs and replace the fuel line if damaged.
If your engine has a fuel pump, replace the pump if it doesn't move gas through the fuel
line to the carburetor.
If you found no problems when checking these fuel system issues, then rebuild or replace
the carburetor to restore the fuel supply to your engine.
If your engine didn't start with the help of starter fluid, check the ignition system.
First, make sure you have the spark plug wire firmly connected to the plug.
Replace the ignition coil if you find damage to the spark plug wire because the wire is
part of the coil.
Here's a video that shows how.
If you found no problems with the spark plug wire, pull the wire off and remove the spark
plug.
Check the spark plug tip for carbon or oil deposits that could prevent the plug from
sparking.
Also, check for cracks in the plug's insulator.
Replace the spark plug if the plug's too fouled to spark or the insulator is cracked.
If the spark plug looks okay, use a spark plug tester to see if the plug it getting
current from the ignition coil.
To test it, install the spark plug and connect the boot of the tester to the spark plug.
Connect the engine's spark plug wire to the other end of the tester.
Crank the engine and see if the tester sparks.
If the tester doesn't spark, it's likely you need to replace the ignition coil.
If the plug sparks, that means the ignition coil is good, but the timing for the spark
might be off.
Here's how the timing works on a riding mower engine.
The flywheel magnet and ignition coil control spark timing.
When the flywheel magnet passes the ignition coil, the coil generates and sends current
to the spark plug, causing the spark.
The flywheel key keeps the flywheel aligned on the engine crankshaft so the magnet passes
the ignition coil at the right time.
The flywheel key is a small metal rectangle that keeps the crankshaft and flywheel aligned
when you tighten the flywheel bolt.
To protect expensive engine components from damage, the flywheel key shears if a mower
blade hits an object with enough force to make the flywheel slip out of alignment with
the crankshaft.
If you hit a rock or stump and the engine suddenly stops, you may have knocked off the
timing by damaging or breaking the flywheel key.
A damaged flywheel key means the magnet won't pass the ignition coil at the right time for
the spark plug to ignite the fuel to start and run the engine.
If this scenario sounds familiar because you did hit an object while mowing and the engine
stopped, remove the flywheel and check that key.
Replace the flywheel key if you find damage.
Here's a video that shows you how.
If you find no problems with the ignition system, then a compression problem could be
preventing the engine from starting.
Check the oil level to see if the engine is overfilled.
Drain some oil to drop it below the maximum fill level.
If the oil level is okay, pull out the spark plug and check cylinder compression using
a compression gauge.
This test shows whether the piston is compressing the air and fuel mixture in the cylinder.
Connect the compression gauge to the cylinder through the spark plug hole.
Zero the compression gauge.
Briefly turn the key to the start position so the starter motor spins the engine.
Check the compression reading.
Most engines should measure over 40 psi of compression.
Many engines produce more than 80 psi.
If cylinder compression is less than 40 psi, the piston isn't compressing air inside the
cylinder.
Keep in mind that a low compression reading shows you that a compression problem exists,
but doesn't reveal the cause.
You might need to adjust the valves or replace the piston rings.
A damaged cylinder wall can also prevent the piston from compressing air inside the cylinder.
To accurately analyze a compression problem, have a service technician do a leak-down test
on the engine.
The technician will use an air compressor and special tools to find where air leaks.
Once the technician finds the cause of the compression problem and fixes it, you can
get back to mowing.
I hope this video helps you out today.
You can find links to the products and parts we talked about in the video description below.
Check out our other videos here on the Sears PartsDirect YouTube channel.
Subscribe and we'll let you know when we post new ones.
For more infomation >> BREAKING Something CHILLING Was Just Found At Mexican Border – CNN Won't Report This… - News - Duration: 1:47. 
For more infomation >> 10 Cool || Facts about Chandigarh || Which Probably you don't know. - Duration: 1:31. 
For more infomation >> Minecraft | Survival Series #1 | Read Desc Below - Duration: 6:50. 
For more infomation >> Vincent N Roxxy Trailer (HD) (English & French Subtitles) - Duration: 1:56. 
For more infomation >> Don't submit - Duration: 0:38. 
For more infomation >> on expectations and doing things we don't want to - Duration: 6:08. 
Không có nhận xét nào:
Đăng nhận xét